Halsey Taylor Parts

The Elkay / Halsey Taylor 61314C Green Spring Cartridge Regulator is one of the most commonly replaced parts in a drinking fountain. It functions as both an on/off valve and a flow regulator.

The Elkay / Halsey Taylor 61313C Red Spring Cartridge Regulator is one of the most commonly replaced parts in a drinking fountain. It functions as both an on/off valve as well as an adjustable flow regulator. It is used on Elkay and Halsey Taylor drinking fountains with a pushbutton

The Elkay 92450C Cartridge Housing is used in Elkay and Halsey Taylor drinking fountains.

The housing holds the cartridge (NOT included) in place.

The Elkay/Halsey Taylor 98531C Green Spring Cartridge Housing Kit is a convenient pre-assembled kit. It will fit in most Elkay/Halsey Taylor drinking fountains with a front push bar and will solve most run on or water leaking issues. Housing is labeled “in” to show where to connect the supply line to, making it an easy installation.

This Elkay / Halsey Taylor 98530C Red Spring Cartridge Housing Kit is a pre-assembled kit that includes the red spring cartridge and the housing. This kit fits most Elkay and Halsey Taylor drinking fountains with a pushbutton.

The Halsey Taylor Bubbler 51544C is a plastic bubbler head with chrome plating and a female inlet. The bubbler head will fit on many Halsey Taylor drinking fountains.

The Halsey Taylor 51546C Plastic Bubbler Head Satin fits on Halsey Taylor drinking fountains.

The water flows through the bubbler head into the drinking fountain basin.

The Halsey Taylor 16-03165-08-640 Bubbler Head Chrome is a brass bubbler head with chrome plating.

This is a genuine Halsey Taylor 97446C Vandal Resistant Bubbler Kit.

The Elkay Strainer 55996C is located at the water inlet of the drinking fountain. The strainer collects and traps any sediment that may damage the valve or other components of the drinking fountain. It fits Elkay and Halsey Taylor drinking fountains.

The Halsey Taylor 60-08050-51-550 Diaphragm Repair Kit is for use with Halsey Taylor drinking fountains.

The repair kit is for repairing the diaphragm regulator.

The Elkay / Halsey Taylor 60290C Cartridge Regulator is used in stainless steel, push button bubbler heads.

The cartridge regulator controls the on/off of water flow and the amount of water pressure.

The Elkay / Halsey Taylor 50212C Pivot Block Pin works with Elkay and Halsey Taylor drinking fountains.

The pivot block pin snaps into the metal push handle and sits inside the pivot block.

The Elkay / Halsey Taylor 51531C Pivot Block fits many older Elkay and Halsey Taylor drinking fountains with push bars. This plastic pivot block mounts inside the drinking fountain. The pivot pin which is attached to the push bar fits into this block. Together the two parts act as a hinge for the push bar to pivot on.

The Elkay Solenoid Valve 35981C is found in the Elkay EZ and Halsey Taylor HTV series water coolers with a model number that ends with an “A” or “B” or with a serial number that is lower than 0807xxxxx.
For Elkay / Halsey Taylor series water coolers with a model number that ends with a “C” or “D” or with a serial number that is higher than 0807xxxxx use part number 98466C

The Halsey Taylor 60-26229-51-550 Right Flow Valve / Regulator is the complete assembly for the valve (celcon) and regulator.

The right flow valve / regulator controls the water flow and volume of water to the bubbler head.

The Halsey Taylor 60-26230-51-550 Left Flow Valve / Regulator is the complete assembly for the valve (celcon) and regulator.

The left flow valve / regulator controls the water flow and volume of water to the bubbler head.

The Halsey Taylor 60-14800-51-550 Right Flow Valve Assembly is an older version of a valve.

The right flow valve assembly controls the flow of water to the bubbler head.

The Universal 7800 Bubbler Head Stainless Steel is a universal push button bubbler head. This bubbler is used on many different models of drinking fountains.

The Universal 1020888 Soft Top Bubbler Head Stainless Steel is a soft top bubbler head with a push button.

The Universal Bubbler Head Conversion Kit will retrofit older twist style valves to a push button bubbler head.

The Elkay Cold Control Thermostat 31513C is an adjustable cold control thermostat. This thermostat controls the cooling system to regulate the temperature of the chilled water in most Elkay and Halsey Taylor drinking fountains. There are two male electrical terminals and one metal sensing lead.

The Elkay / Halsey Taylor 35948C Push Bar Switch mounts behind the push bar. It has two male spade wire connectors.

When the push bar is pressed, this switch sends power to the solenoid which activates the water flow.

The Halsey Taylor 35839C Cold Control Thermostat is an adjustable cold control thermostat. It includes a bracket and sensing lead.

The thermostat controls the temperature of the chilled water that is dispensed.

The Halsey Taylor 92776C Push Button Kit is a complete valve conversion kit replaces #60-15172-51-550 and #60-42278-51-550.

The Halsey Taylor 60-16327-51-550 Complete Valve Kit is for side-mounted drinking fountain valves.

The Elkay / Halsey Taylor 56092C Plastic Tubing 1/4” x 48” is used in Elkay and Halsey Taylor drinking fountains.

The tubing is used as water lines within the drinking fountain.

The Universal 96852CA Glass Filler Kit can be added to most drinking fountains.

The Halsey Taylor HWF 172 Water Filter Kit is designed to remove cysts, lead particles, and chlorine for Halsey Taylor HAC, HACBL, WM, SCWT, S, and WMBL series drinking fountains. The kit includes quick disconnect fittings, outer protective wrap, and an automatic inlet shut-off valve.

The Halsey Taylor 55897C Replacement Filter is a replacement filter for the HWF172. The filter head is not included.

The Halsey Taylor HWF 142 In-Line Water Filter Kit is designed to remove cysts, lead particles, chlorine, taste, and odor for Halsey Taylor HTV series drinking fountains. The kit includes quick disconnect fittings and mounting hardware on each end of the in-line filter.

The Halsey Taylor 56191C Replacement Filter (for HWF 142) is designed to remove cysts, lead particles, chlorine, taste, and odor for Halsey Taylor HTV series drinking fountains. The kit includes quick disconnect fittings on each end of the filter.

The Elkay 70682C John Guest Tee Coupling 1/4” x 1/4” x 1/4” uses 1/4” snap-in fittings.

The tee coupling is used for splitting water lines inside of the drinking fountain.

This is a genuine Elkay / Halsey Taylor 70836C John Guest Elbow Fitting 3/8 X 1/4.

This is a genuine Elkay / Halsey Taylor 70870C John Guest Union 3/8”.

This is a genuine Elkay / Halsey Taylor 70852C John Guest T Coupling 3/8” x 3/8” x 3/8”.

This is a genuine Elkay / Halsey Taylor 70817C John Guest Fitting, 1/4” 90* Elbow F & M.

This is a genuine Elkay or Halsey Taylor 75583C John Guest Elbow 1/4” x 5/16”.

The Elkay / Halsey Taylor 70793C Elbow Fitting 1/4” uses 1/4” snap-in fittings.

The elbow fitting is used for splitting water lines inside of the drinking fountain.

This is a genuine Halsey Taylor 15009C Bubbler Head Nipple.

This is a genuine Elkay / Halsey Taylor 31272C Solenoid Valve.

The Halsey Taylor 10-15143-31-640 Push Bar Insert Chrome mounts on either a front or side push bar. It requires 2 nuts (#102542 – NOT included) to hold the bar in place.

The push bar insert is used as an aesthetic addition to the front of a push bar.

This is a genuine Elkay / Halsey Taylor 56110C Push Bar.

The Halsey Taylor 55859C Push Bar Adapter works on either side of the front push bar.

The push bar adapter mounts between the metal bracket and the push button insert.

The Elkay Cartridge Holder 50986C is used in most Elkay and Halsey Taylor drinking fountains. The housing holds the cartridge(not included). The housing has internal coarse threads for the cartridge retaining nut, and fine external threads for the nut that holds the housing in place. The water inlet and outlet are 1/4” quick connect fittings.

The Elkay / Halsey Taylor 50377C Drain Gasket is a common replacement when there is a leak under the drain.

The drain gasket prevents leaking from the drain.

The Elkay / Halsey Taylor 55884C Drain Elbow 1-1/4” is hard plastic and has a bottom threaded male end. It works with drain gasket #102742.

The drain elbow connects to the drain.

The Elkay / Halsey Taylor 10-03227-40-560 Flat Black Gasket is a a 1” diameter gasket.

The gasket is used to create a seal to prevent leaks.

The Elkay / Halsey Taylor 10031C Retaining Nut has two holes on top of the nut.

The retaining nut holds the cartridge regulator in the housing.

The Elkay / Halsey Taylor 40169C Hex Nut Chrome is used to hold the cartridge regulator housing.

The Elkay / Halsey Taylor 10-01471-40-560 Drain Gasket is a rubber drain gasket that fits against the drain elbow #102495.

The drain gasket creates a seal so water doesn’t leak.

The Elkay / Halsey Taylor 15005C Cartridge Retaining Nut is a plastic nut that holds the cartridge in the housing. This coarse thread nut is for use with newer coarse thread housings.

The Elkay / Halsey Taylor 11-14117-43-620 Nut 1/4” is a self-threading stamped nut.

The nut threads onto plastic studs to secure a push bar in place.

The Halsey Taylor 60-08250-51-550 Twist Valve Repair Kit is for rebuilding twist valves in Halsey Taylor drinking fountains. The twist valve is located on the side of the drinking fountain.

The Elkay 45336C Drain Assembly threads into the drain. The assembly includes the drain flange and strainer.

The Elkay 40322C Stream Breaker threads into bubbler parts #101066 and #107271. It comes with a diverter assembly.

The stream breaker creates a smooth flow of water out of the bubbler head.

The Halsey Taylor 60-14829-51-550 Plastic Stem Assembly fits Halsey Taylor drinking fountains.

The stem assembly threads into the valve body housing to control the water flow.

The Halsey Taylor 60-08240-51-640 Push Button Assembly is for use on Halsey Taylor drinking fountains. The assembly includes parts for a brass push button with chrome plating.

Pressing the push button activates water flow.

The Halsey Taylor 16-02705-08-640 Strainer Plate fits Halsey Taylor drinking fountains. The strainer plate is brass and chrome-plated.

The Halsey Taylor 60-07553-51-590 Push Button Rod Kit is designed for use in Halsey Taylor drinking fountains.

The push button rod presses on the water valve to turn on the water flow in the drinking fountain.

The Halsey Taylor 60-06429-51-590 Push Button Rod Kit is designed for use in Halsey Taylor drinking fountains.

The push button rod presses on the water valve to turn on the water flow in the drinking fountain.

The Elkay / Halsey Taylor 40575C Drain Assembly includes the drain strainer and the chrome-plated ferrule.

The Elkay / Halsey Taylor 22574C Regulator Mounting Bracket fits in Elkay and Halsey Taylor drinking fountains.

The regulator mounting bracket holds the housing and cartridge regulator in place.

The Elkay / Halsey Taylor 20397C Tailpipe 5” is a 5” tailpipe.

The tailpipe is the part of the pipe from the drain down to the waste line.

The Elkay / Halsey Taylor 40619C Tailpipe Ferrule is for Elkay and Halsey Taylor drinking fountains.

The tailpipe ferrule surrounds the drain on the top of the drinking fountain.

The Elkay / Halsey Taylor 40572C Tailpipe 1-7/8” is 1-7/8”.

The tailpipe refers to the pipe running from the drain down to the waste line.

This is a genuine Elkay / Halsey Taylor 31341C Fan Motor.

Kit includes:

• 12 – O-Ring
• 1 – O-Ring
• 4 – O-Ring
• 1 – 1/4 Super Seal
• 1 – 3/8 Super Seal
• 6 – 1/4” Collete
• 1 – 3/8” Collete
• 1 – 1/4” Poly Tubing
• 1 – 3/8” Poly Tubing

Kit includes:

• 1 – Bubbler
• 1 – Bubbler Nipple
• 2 – O-Ring